Actebis 15.06.1120 Datasheet download pdf (Page 1)

DIS PWR

If you are ready with the jumper settings, please proceed with the following installation

instructions. Because the designs of computers are different, only general installation

instructions are given. Please refer your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Com-

puter and gently slide the cover off.

3. Locate an available expansion slot and remove its covers from the rear panel of your

computer. Make sure it is the right expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make

sure the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

HARDWARE INSTALLATION :

6 5

44190

English

44190

English

Die EX-44190 ist eine PCI-Express Multi I/O Karte mit einem Parallel Centronics EPP/ECP

Port und 2 seriellen FIFO 16C95x Ports, für den Anschluss von High-Speed seriellen RS-

232 Peripherie Geräten (z.B. Terminal, Modem, Plotter usw.). Der serielle PCI-Express Bus

unterstützt dabei optimal die Leistung des schnellen 16C95x Chipsets mit 128byte FIFO

Cache. Die Karte gewährleistet so eine sichere Datenübertragung und exzellente Perfor-

mance von bis zu 921KBaud/s für jedes angeschlossene Gerät! Sie unterstützt alle PCI-

Express Slots von x1 bis x16. Es ist nicht möglich die I/O Adressen und Interrupts manuell

einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim Installieren des

Betriebssystems automatisch vorgenommen werden. Mit dem Jumper JP1 können Sie

vom Standard Quarz (1.843MHz) auf den schnellen (14.7456MHz) Quarz umschalten.

Beachten Sie bitte falls Sie mit dem schnellen Quarz arbeiten, dass die Peripheriegeräte

dies auch unterstützen. Im Gerätemanager muss ausserdem die richtige Teilung (Divisor)

& Geschwindigkeit manuell eingestellt werden.

BESCHREIBUNG & TECHNISCHE DATEN :

AUFBAU :

Kompatibilität: PCI Express x1 bis x16

Betriebs Systeme: WIN9x/ME/NT 4.0/2000/XP/Server 2003/Vista/(Linux vom OS)

Anschlüsse: 2 x 9 Pin Sub-D Stecker, 1 x 25 Pin Parallel Buchse

Lieferumfang: EX-44190, Treiber CD, Anleitung, 1 x 25 Pin Slotkabel

Zertifikate: CE / FCC / RoHS / WEEE DE97424562 / WHQL

Windows 9x/ME/2000/XP & Vista:

After starting Windows it recognizes a new “PCI Controller“ and open the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system “95_98_ME“ “2000“ “XP32“ “XP64“ “Vista32“ or “Vista64“ into the box for

the Path/Source and click at >next/continue<. Now Windows search for the drivers in

the specified directory. Follow the hardware assistant and finish the installation. If Win-

dows recognizes other new devices repeat the above described steps. Attention!

Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under ”Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (LPT2) or (Com3). If you see this or similar

entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256. This also works with LPT Ports!

Windows Server 2000/2003:

After starting Windows it recognizes a new “PCI Controller“ and open the hardware

assistant. Please choose manual installation and put the driver CD into your CD-Rom

drive. Now enter the Path "D:\IO\OXFORD\" and then the directory of your operating

system for Server 2000: “2000“ and for Server 2003: “XP32“ or “XP64“ into the box

for the Path/Source and click at >next/continue<. Now Windows search for the drivers

in the specified directory. Follow the hardware assistant and finish the installation. If

Windows recognizes other new devices repeat the above described steps. Attention!

Restart Windows in any case after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at Start<>Run< then enter “compmgmt.msc“ and click at >OK<. In the windows

that open select >Device Manager<. Under „Ports (COM and LPT)“ you should find

one or more new ”PCI Ports“ as sample (LPT2) or (Com3). If you see this or similar

entries the card is installed correctly.

CHANGE PORT NUMBER:

If you like to change the port number for example COM 3 to COM5, open the >Device

Manager< click at >COM3<, >Settings< and then >Advance<. There you can change

between COM 3 till 256. This also works with LPT Ports!

Windows NT 4.0:

Start Windows NT and insert the driver CD into your CD-ROM drive (for example D:).

Click at >Start< >Run< and enter „D:\IO\OXFORD\NT4\Install_Serial.exe" then click

>OK<. Windows NT will now start the setup program and install the driver. Please

Restart Windows NT after installing the drivers.

CHECK THE INSTALLED DRIVER:

Click at >Start< >Programs< >Administrative Tools[Common]< >Windows NT-

Diagnostics< then click at >Resource< >IRQ<. Here you should find the entry „09

oxser 0 PCI“. Then click at >I/O-Port< here you should see the entries „D400-D407

oxser 0 PCI“ „D800-D802 oxser 0 PCI“ and „DC00-DC1F oxser 0 PCI“ for

the ports. The I/O addresses can change depends which system and card is installed. If

you see these or similar entry's the card is installed correctly.

LINUX:

There are no drivers available for Linux, but the card is supported by the most versions

of Linux. Because each individual distribution and kernel version of Linux is different,

sadly we cant provide a installation instruction. Please refer to the installation manual for

standard IO ports from your Linux version! In some newer versions the card will even be

installed automatically after starting Linux.

DRIVER INSTALLATION :

JP4:

AUX5V = DC5V from J8, pc power supply cable is required

AUX12V = DC12V from J8, pc power supply cable is required

PCI12V = DC12V from PCI Express (Factory setting), no cable

Only if JP3 is set to PWR! The pin 9 from the serial port connector

will be supplied with DC5V or DC12V. There are 3 sources depends

on the jumper position of JP4.

JP3: DIS = The pin 9 is connected with the RI (Ring Indicator)

signal as standard RS-232 definition (Factory setting).

PWR = The pin 9 is connected with a power either from PCI

Express slot or from Aux Power connector (J8) The power source is

controlled by JP4 jumper (see the following section).

JUMPER SETTING & CONNECTORS:

DB 9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GROUND 8 CTS

3 TXD 6 DSR 9 RI

Serial 9 Pin D-SUB connector (S1 to S2):

1 +5V

2 GND

3 GND

4 +12V

J8:

AUX5V

AUX12V

PCI12V

JUMPER EINSTELLUNG & ANSCHLÜSSE:

JP1: Mit dem Jumper JP1 können sie zwischen zwei Clock Geschwindigkei-

ten wählen für Kompatibilität oder höhere Baudraten.

LOW = Der Quarz ist auf 1.8432Mhz eingestellt für eine maximale

Baudrate von 115.2KBaud. (Werkseinstellung). Diese

Einstellung ist für die meisten Anwendungen optimal.

HI = Der Quarz ist auf 14.7456Mhz eingestellt für die maximale

Baudrate von 921.6KBaud.

Bemerkung: Bei der Einstellung HI müssen sie im Gerätemanager von

Windows bei den COM Port Einstellungen den Wert des Quarz automa-

tisch suchen und einstellen!

JP2: Die Jumper auf JP2 bitte nicht verändern. Sie sind nur für Testzwecke

im Werk!

M2 = Jumper gesetzt

M1 = Jumper gesetzt

M0 = Jumper nicht gesetzt

LOW

S1 9 Pin Stecker

Seriell Anschluss

S2 9 Pin Stecker

Seriell Anschluss

JP3 Power auf 9 Pin Stecker

Ein / Aus

JP2 UART Mode Einstellung

(Nur für Testzwecke im Werk)

JP1 Umschalter

(für Datentransfer

über 115.2KBaud)

S1- Interne

S2 Serielle

Anschlüsse

JP4 Jumper für die

Stromquelle

(Netzteil oder PCI-

Express Bus)

J8 Anschluss für den

Power vom Netzteil

P1 25 Pin Buchse

Parallel Anschluss

J7 Interner Parallel Port

für 25 Pin Kabel

DB 25F:

Pin Signal Pin Signal Pin Signal

1 STROBE 10 ACKNOWLEDGE 19 GROUND

2 DATA 0 11 BUSY 20 GROUND

3 DATA 1 12 PAPER EMPTY 21 GROUND

4 DATA 2 13 SELECT 22 GROUND

5 DATA 3 14 AUTO FEED 23 GROUND

6 DATA 4 15 ERROR 24 GROUND

7 DATA 5 16 INIT 25 GROUND

8 DATA 6 17 SELECT INPUT

9 DATA 7 18 GROUND

Parallel 25 female connector (P1):

Bedienungsanleitung

Vers. 3.0 / 12.04.07

For power over pc power supply J8 must be connected!

1 2

Bedienungsanleitung 1
User Manual 2

Summary of Contents

Page 1 - Bedienungsanleitung

S1 S2 DIS PWR If you are ready with the jumper settings, please proceed with the following installation instructions. Because the designs of computers

Page 2 - User Manual

2 3 4 EXEXEX---441904419044190 DeutschDeutschDeutsch EXEXEX---441904419044190 DeutschDeutschDeutsch The EX-44190 is a plug & play high-spe

Comments to this Manuals

No comments

Actebis 15.06.1120 Datasheet Page 1

Browse online or download Datasheet for Interface cards/adapters Actebis 15.06.1120. Actebis Exsys EX-44190 PCI-Express 2S/1P Multi I/O card User Manual

Summary of Contents

Comments to this Manuals

Actebis 15.06.1120 Datasheet Page 1

Browse online or download Datasheet for Interface cards/adapters Actebis 15.06.1120. Actebis Exsys EX-44190 PCI-Express 2S/1P Multi I/O card User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Interface cards/adapters Actebis 15.06.1120